How do I convert a toilet drain to a shower drain

Unscrew the old toilet flange and pry it loose. … Join the 4-inch to 2-inch PVC reducer bushing to the sewer pipe with a 4-inch rubber coupling, if the pipe is metal or non-PVC. … Temporarily mount a 2-inch PVC trap under the shower drain location with a pipe hanger.

Can you convert a toilet drain into a shower drain?

If you are remodeling your bathroom and find that the shower will be installed over the location of the previous toilet, you can simply change the toilet drain to a shower drain.

Are shower and toilet pipes connected?

The toilet and shower drain are connected to the main pipe. The outside of the main sewer drain is connected to the shower and Toilet Drain. The extra waste-water comes from your home to the main sewer line.

How do I turn my toilet into a shower?

1. Turn off the water supply for the toilet at the wall. …
2. Unscrew the bolts that hold the tank to the toilet. …
3. Use a utility knife to cut through any caulk holding the toilet bowl to the floor. …
4. Rock the bowl gently back and forth to free it from the O-ring.

Can you put a tub where a toilet was?

The toilet will also only have a cold water supply. The tub drain pipe will likely be 1 1/2″, and will have a trap. The tub will obviously have both cold and hot water supplies. To switch the location of the fixtures, you’ll have to reroute the plumbing for each to the new locations.

Can toilet and shower share same vent?

Wet vents are typically used when plumbing a bathroom group. So yes the shower can also be vented by the wet vent along with the toilet. There is one major stipulation when wet venting multiple fixtures when a toilet is one of them: the toilet must be the last fixture connected to the wet vent.

How much fall does a shower drain need?

To efficiently drain, the recommended minimum slope for a shower floor is about 4 percent, or a 1/2 inch drop per every 12 inches from the shower walls to the drain. In traditional tile shower construction, this slope is established in the mortar pre-pan.

How far does a toilet need to be from a shower?

A minimum clearance in front of the toilet of at least 21 inches. This is required for all your bathroom fixtures, including the shower, vanity or sink and bathtub. A minimum distance from the center of the toilet to both side walls of 15 inches.

How much space should be between toilet and shower?

Plan a clear floor space of at least 30 inches from the front edge of all fixtures (lavatory, toilet, bidet, tub, and shower) to any opposite bath fixture, wall, or obstacle. Code Requirements: A minimum space of 21 inches must be planned in front of the lavatory, toilet, bidet, and tub.

How far can you move a toilet from the stack?

If your waste line has a diameter of 3 inches, you can place the toilet within six feet of your stack. The toilet can also be as far as 10 feet from your stack, if the diameter of the waste line is 4 inches.

Article first time published on

How do you Slope a shower drain pipe?

The ideal slope of any drain line is ¼ inch per foot of pipe. In other words, for every foot the pipe travels horizontally, it should be dropping ¼ inch vertically.

Does a shower drain need to be vented?

It’s easy to forget, but it’s a vital and required part of any plumbing fixture drain. The vent pipes remove sewer gases while allowing air into the system to help the water drain. Without a vent, your shower won’t drain correctly.

Is a shower drain the same as a toilet drain?

Most shower drains are 2”, while the minimum for a toilet drain is 3”. This means that you are going to have to replace the shower drainpipe, so it is big enough to fit the toilet.

What should I use to unclog a shower drain?

Mix together 1 cup of vinegar (distilled white vinegar works best) and 1 cup of baking soda. First, pour boiling water down the drain to loosen; then follow with the baking soda-vinegar mixture and wait 15 minutes. Rinse with more boiling water.

What is wet venting?

So what is wet venting? Traditional wet venting is the venting of one or two bathroom groups. A bathroom group includes all the fixtures located within a bathroom, such as a water closet, lavatory, bathtub, shower or bidet. All these fixtures can be vented with a single dry vent.

Why is the toilet always next to the shower?

Toilets tend to be next to bathtubs because both of them tend to be in a small room that is kept rather private from the rest of the house and because both of them need to have fairly substantial plumbing in order to operate correctly.

Can you replace a 10 inch rough in toilet with a 12 inch rough in toilet?

The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.

How big does a shower need to be without a door?

A doorless shower layout requires a larger footprint than a standard tub or shower stall. Building codes may specify that a standard shower stall must be a minimum of 36 inches by 36 inches while the average doorless shower is about seven feet by four feet with many much larger.

How wide should a shower be?

As for size, your shower should be at least three feet square and have a wide entry, so there’s ample room to get in and move around. Designer Mary Jo Peterson, CKD, CBD and a universal design specialist in Brookfield, Conn., says 42 by 60 inches is even better, particularly for showers that have no door or curtain.

What is an advantage of a wall mount water closet?

Wall-mounted toilets can save as much as 10 inches by moving the tank into the wall. And the bowl itself can be adjusted to sit anywhere from 15 to 19 inches off the ground. Wall-mounted toilets come at a premium over standard toilets.

Is it difficult to relocate a toilet?

Moving a toilet is not so much about moving the actual fixture—in fact, installing a toilet is a simple job that takes less than an hour—as it is about moving the drainage and the water supply plumbing to the new location. Once all of the plumbing is in place, installing the toilet is a relatively easy task.

Can you relocate a shower?

When moving a shower, you’ll also need to install the shower head in the new location. You can either have your current shower head reinstalled or choose a brand new one. … This also requires plumbing expertise, especially if you decided to attach the shower head to newly installed pipes.

Is it expensive to relocate a toilet?

The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move. Connecting the toilet to the existing sewer line can be a bit tricky for your plumber.

What is the pitch for a toilet drain?

The plumbing code requires drain pipe to be sloped at a minimum of 1/2 inch per foot and a maximum of three inches per foot or vertical. A slope of less than a quarter-inch per foot will cause a lot of drain clogs and a slope of more than three inches will allow the water to drain.

Why does a shower require a 2 inch drain?

A 2-inch pipe is the recommended size because showers have a low threshold for flooding, and a 2-inch pipe helps the water drain faster than does a 1 1/2-inch pipe. So, if you are converting from a tub and shower combination to a shower, you’ll likely have to change the drain pipe size.

How far can vent be from shower drain?

The connection between the fixture drain and the horizontal drain and vent pipe is the only vertical pipe of a combination drain and vent system. 8 feet is the maximum vertical distance.

What happens if plumbing is not vented?

Poorly-vented drain lines will not be able to effectively move wastewater and solid waste out of your building. This could lead to problems such as overflowing drains, backed-up toilets, and similar plumbing issues.

Does a walk in shower Need AP Trap?

Yes, shower and tub drains require a trap in the plumbing to prevent harmful sewer gases from coming into the home.

Are shower and sink drains connected?

All of the sink, toilet, tub/shower and dishwasher drains connect to one main drain line that empties into a municipal sewer system or into your septic system (or cesspool.)