How do you use self leveling compound on plywood subfloor

If you’ve got a plywood subfloor, like many buildings do, you can leave it in place and apply self-leveling concrete directly on top of it. … You can also use self-leveling concrete on plywood as an underlayment for other types of floor coverings, such as carpet or tile.

Can you put self-leveling compound on plywood?

If you’ve got a plywood subfloor, like many buildings do, you can leave it in place and apply self-leveling concrete directly on top of it. … You can also use self-leveling concrete on plywood as an underlayment for other types of floor coverings, such as carpet or tile.

How do you flatten plywood subfloor?

“If you’re going to float a plywood subfloor over a concrete slab, and you just want your sub-base to be flat, you could do something as simple as putting dry sand down,” or using pieces of sheet vinyl as shims, says Moore.

Can you level a plywood subfloor?

To level a subfloor for installing laminate, follow the directions above to remove high and low spots. After vacuuming or sweeping the subfloor to clean it, add a plywood layer if the subfloor is in very bad shape, but do not overlap the sheets. A plywood layer is not necessary if you are putting down wood laminate.

How do you fix uneven plywood subfloor?

Using a flat-edged trowel, apply the floor leveling compound. Fill in all dips and uneven spots in the subfloor. Allow the leveler to dry as is instructed by the manufacturer’s product label. Remove hills or humps using a floor sander until the entire floor is level.

Can you use thinset to level a plywood floor?

Well, the answer is actually no. Mortars cannot be used to level or patch a floor – ever! … The most versatile self-leveler is Novoplan 2 Plus, a high-strength, cement-based underlayment and repair mix for use over interior concrete, plywood and other approved floor surfaces.

How do you level a sloping floor with plywood?

Place strips of plywood across the floor to fill deeper slopes, increasing the thickness of the plywood at regular intervals to correct the slope. For example, fill a 1-inch slope across 8 feet by putting a 12-inch strip of 3/8-inch plywood at the point where the slope is that deep.

How do you level a subfloor for a floating floor?

Thoroughly vacuum the existing floor, and use a long floor leveler and tape measure to ensure the subfloor is level within 3/16 inch for every 10 feet. You’ll need to know how to level a floor: Just sand any high spots and fill the low spots with leveling compound.

How do you fix an uneven subfloor?

For concrete slabs: If there are only a few problem areas in the concrete, you can mechanically flatten them by grinding, bead-blasting, abrading, or using a patching compound. If the entire slab is uneven, you may have to use a self-leveling concrete compound to smooth it out.

How much does a 50 lb bag of self leveler cover?

Coverage: One 50 Lb. bag will cover approximately 40 Sq. Ft. at 1/8 In.

Article first time published on

How do you level an existing subfloor?

1. Identify and Prepare the Low Spots. Mark the areas of the floor that need filling in to bring them level with the surrounding areas. …
2. Mix and Apply the Self-Leveling Compound. …
3. Lightly Sand.

How do you use thinset to level a floor?

1. Tape a string down from one high point in the floor to another high point in the floor. …
2. Pour thinset powder into a bucket and add water. …
3. Spread the thinset over the surface, filling in the low spots and holes. …
4. Allow the thinset to set until it is almost dry.

Do I need primer for self leveling compound?

Primer. All of the self leveling cements require that you buy bottles of primer as well to coat your floor with prior to pouring the concrete. It is a rule but it’s only applicable if you’re pouring cement onto cement. If you have a non porous surface as your base primer isn’t crucial.

Can you use self leveling on wood?

Wood floors need to be primed before covering them with self leveler. The floor will be covered with water-saturated leveler, which will cause the wood to swell. It will shrink back down when it dries, which could cause cracks in the underlayment and tiles above. The primer prevents the wood from absorbing water.

How do you level a sloping wood floor in an old house?

1. Pour Self-Leveling Underlayment. Pour self-leveling underlayment in the problem area. …
2. Sister the Joists. …
3. Prop Up the Joists. …
4. Lay Down New Hardwood.

Can thinset be used on plywood?

Thinset is the wet base that you first trowel on the plywood to make the tile stick. Higher latex content is essential for bonding to plywood. A quality unmodified thinset should be used and mixed with a latex additive.

Can I put thinset over self leveling compound?

3 Answers. Yes you must remove all of the thinset – FOR SURE. Thinset is not meant to be exposed and a leveler on top of it will not protect it enough.

Is mortar the same as thinset?

The word “thinset” is sometimes used interchangeably with “mortar,” because it’s a type of modified mortar made specifically for tile. Thinset is made of sand, water, and cement, and can also contain additives for increased bonding, water resistance, and flexibility.

What do you put on top of subfloor?

Underlayment: Some types of flooring can be installed directly on top of the subfloor, such as vinyl flooring. Other types need a middle layer, called underlayment, such as laminate,carpet and tile.

How thick can you go with self leveler?

QUIKRETE® Self-Leveling Floor Resurfacer (No. 1249-50) can be installed from 5/8 inch (16 mm) thick to a feather edge. For areas deeper than 5/8 inch (16 mm), apply QUIKRETE® Self-Leveling Floor Resurfacer (No. 1249-50) in layers no greater than 5/8 inch (16 mm) each.

How thick should subfloor plywood be?

The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch.

How flat does subfloor need to be for laminate?

Most manufacturers recommend that the floor be flat to within 3/16” in a 10 ft. radius. These measurements are consistent with most other types of floor coverings. On floating floors, vertical movement needs to be kept to a minimum.

How many bags of self leveling do I need?

Self-Leveling Underlayment (35 Bags/Pallet)

How long does it take for floor leveling compound to dry?

Do not walk on the resurfaced floor until it has fully gained sufficient strength. This is approximately 1 to 2 days for the Normal Set product or 2 to 4 hours for the Fast Set product, depending on surrounding conditions. No special curing steps are required.

What area does a bag of self leveling cover?

It’s suitable for foot traffic in 30 minutes and ready to tile onto in 45 minutes. Sealed coverings such as vinyl can be laid on top of the surface just 90 minutes after application. A 20KG bag will cover 5m² at 3mm, 3.1m² at 5mm, 1.5m² at 10mm and 1m² at 15mm.