How far should shingles overhang

Yes. Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.

How far should shingles hang over roof edge?

The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.

How much should a roof overhang the fascia?

The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger. The shingles should also overhang the drip edge 3⁄8 to 1/2 an inch.

Should shingles overhang gutters?

Most shingle manufacturers recommend a 1/4 to 3/8 inch overhang over your eave, which is where your roof ends by your gutter. In many cases, and particularly as home ages and settles, the roof edge at the eave edge can wave in and out by more than this amount.

Should drip edge be tight to fascia?

A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.

How far should shingles overlap gutters?

Saw gutter to length If the gutter continues around a corner, cut the appropriate angle (typically 45 degrees) on that end. If the run requires two sections of gutter, overlap them by 8 inches and use a 3/8-inch-long, self-tapping, stainless steel screws or pop rivets, in two rows of four each, to join them.

How much should a starter overhang for shingles?

Starter shingles should always overhang the eave and rake edges of the roof by about 1/4″-3/4″ to ensure adequate rain water drainage. It is also important that the seal strip is placed facing up and close to the edge of your roof; otherwise, your roofing system won’t seal properly.

How much should roof overhang gutters?

How Far Should Gutters Be From the Roof Edge? A safe distance between the gutter and the roof edge should be between 2 to 3 inches. If the gutter distance is more than 3 inches, the rain will run off the roof and won’t drain properly.

How do you extend a shingles overhang?

To fix an overhang that’s too short, buy some aluminum drip edge (aka drip-cap flashing). It’s typically sold in 8-ft. lengths, and can be cut with tin snips or even poultry shears. Slide the wide, flat flange of the flashing under the first course of shingles and adjust it to extend over the gutter.

Do you need a roof overhang?

A roof overhang is an essential part of your roofing system to protect your house. If you are simply adding function and protection, or if you want to incorporate a new style to update the exterior of your home, a new roof overhang is a good idea.

Article first time published on

Should you remove the plastic strip on shingles?

The GAF shingle application instructions for our entire product line specifically state that that film does not need to be removed. Note: The film strips on the back of each shingle are to prevent sticking together of the shingles while in the bundle. Their removal is NOT required during application.

How far can Eaves overhang?

Two feet is the general maximum length for a typical roof overhang. This will protect a roof from most types of damage. Roof overhangs can extend farther than 2 feet, but beyond this length, they begin to lose structural integrity and require external support.

Do you put drip edge on before tar paper?

Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

Does the gutter go under the drip edge?

It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. … If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.

How do you measure a roof for shingles?

To estimate how many shingles you’ll need, first estimate the total square footage of your roof’s surface. To do this, measure the length and width of each plane on the roof, including dormers. Then, multiply length x width to get the square footage of each plane.

How long can a gutter be with one downspout?

To limit the effects of thermal expansion in gutters 50 ft(15.3 m) is a practical maximum length of gutter to be served by a downspout.

How much slope does a gutter need?

A sharp gutter slope reduces the water capacity of the gutters, looks strange and can cause water to splash outside the gutters during heavy rain. A good rule of thumb for a gutter slope is that you want at least a quarter inch of slope for every 10 feet of gutters.

What is the roof overhang called?

What Is a Soffit? Your roof by necessity, will often times extend over the walls of your home. This overhang can go by a few names, such as the house eaves or the rafters of your roof. The underside of this overhang, when given a finished appearance, is known as the soffit, which means “something fixed underneath”.

How do you extend a gable end roof overhang?

Attach fascia board at the edge of the overhang. Install roof deck sheathing extended over the gable framing and installed with correct fasteners and fastener pattern. Install a rigid soffit material such as structural sheathing plywood or OSB to cover the underside of the overhang.

How far should shingles be from drip edge?

Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.

Should roofing nails go through the sheathing?

It is crucial that roofing nails of the correct length were used to secure the shingles. The sharp tip of the roofing nail should pass through and extend approximately 3/8-inch past the underside of the roof sheathing.

What is the minimum length of a roof overhang?

There is no true standard size for overhangs, but typical overhangs that are used for protection from rainfall are 16-18 inches wide. Overhangs wanted for shading should be minimally 24 inches.

What is the purpose of a roof overhang?

Purpose. The main purpose of an overhang is to give the house protection against strong winds and heavy rain. Aside from preventing water from running over the edge of the house, snow and other debris are also caught by this extended edge.

How many nails should be used per shingle?

General Guidelines for Nailing Shingles Install the recommended number of nails per shingle. For Duration® Series shingles, Owens Corning recommends using either a 4- or 6-nail fastening pattern depending on the roof’s slope and building code requirements. In most cases, 4 nails are adequate.

How long do shingles take to seal?

Time and Other Considerations Curing time for the tile adhesive seal depends on the manufacturer and should be taken into consideration when selecting the season for installation. In general, ceiling tiles take 48 hours to cure after activation of the strips.

What is the purpose of a shingle starter strip?

Starter strips are an important and integral part of an asphalt shingle roof system. They aid the roof’s water-shedding function by covering shingle joints (and cutouts in traditional three-tab shingles) at the eaves.

How much overhang should a patio roof have?

Typically, a porch overhang should be at least 12-inches long. However, they can range from two feet to very minimal in length depending on the area’s climate, so be sure to account for the amount of rainfall you might expect. Drier climates require minimal overhang length and wetter climates require longer overhangs.

Can you add roof overhang?

A roof overhang protects the building under it from rain and weather, and if your house doesn’t have one, adding an overhang is not an especially difficult construction job. Framing a new overhang is straightforward, but blending the new overhang seamlessly into the existing roof requires some effort and expense.