What does lf mean on Maytag 2000 Series washer

This means shutting off the water supply, and disconnecting the water inlet hoses from the washer. Once the hoses are disconnected, you may have to scrape the sediment from the screens using a knife or sharp object. CLICK HERE for more information on your inlet hoses.

What does code LF mean on Maytag washer?

If F8 E1 or LF (too long to fill) appears in display, the washer is taking too long to fill. … Either the F8E1 or the LF error codes may indicate there is some problem with the water supply going to the washer. Please make sure both inlet hoses are connected and both hot and cold water supplies are turned on.

How do I reset my Maytag washer?

1. Press the “Power/Cancel” button. …
2. Push the appropriate button to choose a new cycle.
3. Press “Start/Pause.” You have now reset your Maytag washer.

What does FL Lo mean on my Maytag washer?

The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. … Press the power button, and the washer will start a drain routine, which takes approximately 8 to 10 minutes, during which time the pump will run continuously. The control will not accept any input during this time.

How do I fix the LF on my washing machine?

LF in the display Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

What are the codes for a Maytag washer?

Error CodeErrorSud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,F8 E1 or LO FLThe washer is sensing a low flow of water.

What does Fl mean on washer?

If Samsung Washer FL Error Code appears on the display panel, it’s likely a door lock malfunction. It indicates the door lock cannot be locked after several attempts.

How do you force a Maytag washer to drain?

1. Pull the washer away from the wall and turn off its power and water connections.
2. Scoop out any remaining water in the washer drum.
3. Unhook the drain hose from the wall or sink drain and empty residual water into a bucket.

What is the capacity of a Maytag 2000 Series washer?

Capacity: 5.2 cu.

Why is my Maytag washer not spinning?

One of the most common reasons for a Maytag top load washer not spinning is an incorrect wash cycle or spin setting. GENTLE, HANDWASH, or DELICATE settings utilize slower spin speeds for more fragile fabrics. Some model washers also allow you to vary the spin speed, making it slower or more rapid, for different loads.

Article first time published on

What does DRN mean on Maytag washer?

drn. One of the most common Whirlpool washer error codes, drn signifies a draining issue. There are several possible problems that result in this code being displayed. These are the most likely causes and solutions for a drn error code: Clogs: A blocked drain hose can prevent proper draining.

What does LF stand for on a Whirlpool washer?

Whirlpool washer error code LF indicates a LONG FILL. NO WATER IS DETECTED entering the washing machine. The error code LF relates to WATER FLOW ISSUES. This means a problem occurs because WATER IS NOT PROPERLY SUPPLIED to the washer.

How do you clean the water inlet valve on a washing machine?

Remove the water inlet screens with your finger or a pair of needle-nose pliers. Brush out any dirt or grit. You can soak the inlet screens in a mild solution of water and vinegar if they are calcified.

What does lf mean on dryer?

An LF (Lint Filter) Error Code indicates that the HybridCare™ filter has been removed. Place filter into dryer and make sure the handle is properly seated.

How do I fix F5 on Maytag washer?

The F5 E2 alert indicates the washer can‘t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.

What does UL mean on a Maytag Bravos XL washer?

@benlogali9 the UL code is for Unbalanced Load. uL is displayed when the machine/motor control detects an off-balance load, and is steady on while the washer runs a mini-cycle to rebalance the load. • Display clears if mini-cycle successfully rebalanced the load.

Where is the inlet valve screen on a washing machine?

It is typically located right behind the washer. There may be two valves that supply hot and cold water to the washing machine inlets.

What does E1 mean on Maytag washer?

If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation.

What does low flow mean on a washing machine?

If you only notice low water pressure when using the hot water setting, then you probably have a clogged hot water line (or vise-versa for cold water). The easiest solution to this problem is to replace the clogged line with a new one. Water lines can be purchased either online or at most major home improvement stores.

What is FL error code?

It means that the contact disappears somewhere between the hatch lock and the control module path. You will have to remove the lock module. Then, using a multimeter, check the loop on contacts leading from the lock.

How old is a Maytag 2000 Series washer?

Maytag (USA) – 24 Year Cycling CodeCodeYearYearY19762000Z19772001A19782002

Do Maytag washers have filters that need to be cleaned?

Do not attempt to remove the filter while the machine is on. Washers and dryers such as those by Maytag have filters to catch lint. … While dryer lint filters and screens should be cleaned out after each use, washing machine lint filters can be cleaned out less frequently.

Where is the filter on a Maytag top load washing machine?

The filter or trap is generally located inside the machine’s agitator.

How do I clean my Maytag washer without affresh?

If you don’t have affresh® tablets, you may be able to use liquid chlorine bleach. Check your owner’s manual for instructions on how to clean with bleach. Close the door and select your washer’s cleaning cycle. For top load washers, when the cycle ends, run a rinse and spin cycle to clear away any excess cleansers.

How old is my Maytag washer?

Find the year and month code. Each Maytag serial number contains two letters. These represent the year and month of manufacturing. They should be the ninth and 10th characters of the serial number.

Is there a recall on Maytag washers?

Hazard: If the front-load washer is operated at maximum load capacity, the spinner could malfunction and break apart, posing a safety risk to consumers. Description: The recall involves white Maytag front-load washers with model number MAH9700 and a serial number from 10188468GA through 11683946GJ.

What does 5d mean on Maytag washer?

This error code indicates excessive detergent suds occurred during the cycle. This could be caused by using too much detergent or not using High Efficiency (HE) detergent. The washer will not be able to spin out water with the excess suds.

How do I get my Maytag washer to drain and spin?

A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.

What causes a washing machine not to drain and spin?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

How do you balance a Maytag commercial washer?

Place a 4-foot level across the front top of the washer. Adjust the front legs if necessary until the front is in balance. Loosen the retaining nut with the adjustable wrench and turn the feet as necessary until the front balances. Tighten the nut with the adjustable wrench.

How do I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.