What is Rift quartered

Logs are cut with the grains intersecting the face of the board at an approximate 60-degree angle. The log is sawn into four quarters and each quarter of the log is sawn perpendicular to the growth rings at an angle, therefore being named rift and quartered.

What is better rift sawn or quarter sawn?

Due to the position of the growth rings in the cut, Quarter Sawn lumber is more dimensionally stable than Plain Sawn. It resists expansion and contraction on plank’s width. Rift Sawn lumber is the most elite of the cuts.

What is rift cut flooring?

Rift sawn White Oak refers to flooring boards that are cut from White Oak timber in a way that produces very straight grain patterns and inherently stable planks.

What is Rift quartered white oak flooring?

Rift and Quartered White Oak contains both straight rift sawn grain and quarter sawn grain. There is naturally occurring fleck on a small percentage of this product that adds to the unique beauty of this highly sought after cut. Rift and Quartered White Oak is prized among wood aficionados all over the world.

What does rift cut oak mean?

Rift sawn lumber is typically narrow with a very straight grain pattern on the face of the board. Rift sawn lumber is usually used with oak to avoid the flecks that are common in the species. … Similar to quarter sawn lumber, rift sawn lumber is also referred to as radial grain.

What does Quartersawn guitar neck mean?

Some high-end guitars and basses have “quartersawn” necks. … “Quartersawn” is a woodworking term that describes a certain specific and non-standard method of milling lumber from trees. Quartersawn instrument necks are unusually strong, straight-grain necks superior to standard necks in almost every way.

What is Rift quartered flooring?

Rift and Quartered Grain Hardwood only has a straight grain with flecking when sawn into four quarters and cut at a 60-degree angle. In other words, only rift and quartered grain can have a straight grain with flecking because of how it’s milled.

What does rift white oak mean?

Rift-Sawn White Oak is similar to Quarter-Sawn, but with the angle of the cut changed slightly so that fewer saw cuts are parallel to the medullary rays, which are responsible for the flake effect. This positions the growth rings between 30- and 60-degree angles to the face of the board.

How can you tell if a wood is quarter sawn?

A board with growth rings running roughly parallel—usually in arches—relative to the face of the board is called a plain-sawn (or flat-sawn) board. If the growth rings are at a steep angle relative to the face, the board is said to have quartersawn grain.

Is quarter sawn white oak expensive?

Review. While quarter sawn oak is more expensive than plain sawn, the value it provides in terms of structural integrity and beauty make it the obvious choice for anyone looking for a quality piece.

Article first time published on

What are the disadvantages of quarter sawing?

More expensive than plain sawn material Quarter sawn wood is more expensive because it is more labor intensive to produce and the manufacturing process produces more waste than plain sawn lumber.

What does rift sawn oak look like?

Rift sawn lumber is typically narrow with a very straight grain pattern on the face of the board. Rift sawn lumber is usually used with oak to avoid the flecks that are common in the species. The annular rings or a rift sawn board are about 30-60 degrees to the face of the board, but 45 degrees is the most optimum.

Is quarter sawn lumber stronger?

Quartersawn wood is generally much stiffer across the grain than flatsawn wood, and for instrument tops this may be advantageous.

What is the difference between quarter sawn and rift cut oak?

Rift sawn lumber, also known as straight grain, is cut at the sawmill with the grains intersecting the face of the board at an angle between 30 and 60 degrees and quarter sawn lumber is cut with the grains intersecting the face board the board at an angle between 60 and 90 degrees.

What are the densest woods?

The densest of all woods is Allocasuarina luehmannii. Krugiodendron typically has a higher density, among many other woods that vary by sample. Various other hardwoods may also be called lignum vitae and should not be confused with it.

How Quarter sawn wood is cut?

Quarter sawing gets its name from the fact that the log is first quartered lengthwise, resulting in wedges with a right angle ending at approximately the center of the original log. Each quarter is then cut separately by tipping it up on its point and sawing boards successively along the axis.

What are the disadvantages of back sawing?

• Home.
• Wood Species.
• Wood Products.
• Sawn Timber.

What are disadvantages of live sawing?

• shrink more across width when drying.
• more likely to warp and cup.
• collapsed timber more difficult to recondition.

Why is quarter sawn better?

Quarter-sawn wood is more stable than plain-sawn. Not only is it less prone to cupping, it also expands and contracts less. Quarter-sawn provides a “quieter” and straighter face grain than plain-sawn.

What is quarter sawn white oak?

Quarter Sawn White Oak is the same species as White Oak but the wood has been cut from the log at a different angle (quartered). It is more stable than standard (flat sawn) White Oak and has a finer texture with a dramatic flaking pattern that runs perpendicular to the grain.

What does Quarter sawn maple look like?

When maple is quarter-cut the figure appears as vertical flame lines. The same appears in Koa wood. However, the same figure appears curly when viewed on plain-sawn grain. In truth, the same vertical flame lines appear when quartersawn or plain-sawn.

How do I know if my guitar neck is quarter sawn?

Cutting the neck blanks in a different orientation to the log will result in the neck having a different grain structure. You can see what your guitar has by looking at the top of the headstock. The image at the top of the page shows a Quarter Sawn neck on the left and Flat Sawn neck on the right.

What is quarter sawn lumber sometimes called?

Quarter sawing or quartersawing is a woodworking process that produces quarter sawn or quarter-cut boards in the rip cutting of logs into lumber. The resulting lumber can also be called radially-sawn or simply quartered.

What does quartersawn oak look like?

Quarter sawn lumber is defined as wood where the annular growth rings intersect the face of the board at a 60 to 90 degree angle. When cutting this lumber at the sawmill, each log is sawed at a radial angle into four quarters, hence the name. Dramatic flecking is also present in red oak and white oak.

Is rift sawn or quarter sawn more expensive?

Rift and/or Quarter Sawn is a premium cut and is generally more expensive than Plain Sawn. It is also considered more stable because of the vertical grain orientation.

What is rift and quarter sawn oak flooring?

In Quarter Sawn flooring, the log is first quartered, and then each quarter is cut again into slices. … Rift sawn flooring is manufactured by milling perpendicular to the log’s growth rings producing a linear grain pattern with no flecking. This method produces the most waste, increasing the cost of this lumber.

What is live sawn?

Live Sawn is a European approach to cutting lumber. Plain sawn is the modern way of sawing lumber, in which the log is turned till the Sawyer can cut off the clearest board. In live sawn, the logs are sliced directly through without turning the log.

What is a disadvantage of rift sawn lumber?

Cons to Rift Sawn Lumber Cost: Because it is so labor-intensive, rift-sawn wood costs more than quarter-sawn or plain-sawn lumber. Waste: Rift-sawn wood produces the most wood waste of the three methods, which is another reason that it’s more expensive.

Is Tiger oak and quarter sawn oak the same?

According to Hunker, tiger oak is lumber made through a specific method of milling called quarter sawing that results in distinctive grain lumber used in high-end applications. … However, quarter sawn oak strictly refers to tiger oak. The difference in plain sawing and quarter sawing is the angle used.

Why quarter sawn timber is the most expensive method of conversion?

Quarter sawn – This is the most expensive method of conversion because it produces the best quality wood and is ideal for joinery purposes. This is because the boards are radial sawn and have very little tendency to shrink or distort.

What are the advantages of rift sawing?

Rift Sawn Advantages: Produces the strongest possible boards with the most consistent visual look of long and straight grain patterns. Generally the choice of cut for fine furniture makers looking for consistent patterns throughout their design. These are the most common ways to mill a log into flooring planks.