What is roof rake edge

Simply put, a roof rake edge is installed to cover the top edge of the siding where it meets the roof. You can think of it as a type of awning that is designed to allow water to flow off the roof and down onto the ground below, instead of down the side of your home.

What is the rake line of a roof?

Rake—The slanting edge of a gable roof at the end wall of the house. Ridge—The horizontal line at the top edge of two sloping roof planes. Sheathing—The decking material (usually sheets of plywood), which is nailed to the rafters, and to which shingles or other outside roofing materials are secured.

What is a rake drip edge?

A drip edge on a roof is a corrosion resistant material that is applied at the eaves and rakes, under the shingles and against the fascia, to improve the efficiency of your roof’s water shedding ability.

Is rake edge necessary?

Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.

What's the difference between a drip edge and a rake edge?

It involves the point of application in relation to the underlayment and/or eaves flashing. At the rake edge, the perimeter drip edge metal is applied over the underlayment with the appropriate fasteners secured every eight (8) to ten (10) inches on center.

Do gutters go on rakes or eaves?

Rain gutters should be positioned to extend beyond the eaves of a roof to collect rain and hail runoff. Gutters are placed on all sides of a home along the roof edge.

Where are the rakes on a roof?

So, what is the rake of a roof? Well, the rake of a roof is the exposed portion on the sides of a gable roof that extends from the eave to the ridge of the sloped sides. The rake of a roof covers the top edge of the roof. This is also an area of the roof where leaks can often occur.

Should gutters be installed under drip edge?

It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. … If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.

Do you need drip edge on rake edge?

Just like normal drip edge, aluminum fascia and rake molding goes along the eaves and covers the edge of your roof’s deck to prevent water from going where it’s not supposed to. If your home has either one, you don’t need drip edge.

Should drip edge be tight to fascia?

A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.

Article first time published on

Does roofing felt go over or under drip edge?

1 Answer. It depends on where the drip edge is. At the side, or gabels, of a roof, the drip edge goes over the roofing felt. At the bottom of the roof, the drip edge goes under the roofing felt.

What is rake trim on a metal roof?

Also known as rake trim, gable trim is a finishing piece of metal flashing used along the edges of a metal roof line where the edge of the metal roof panel meets the endwall panels.

Why is water dripping between gutter and fascia?

If water is dripping behind your gutter, it’s probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter. Home centers sell a gutter apron in 10-ft.

What is a rake overhang?

The American Wood Council’s 2012 Wood Frame Construction Manual defines rake overhang as “The horizontal projection of the roof measured from the outside face of the gable endwall to the outside edge of the roof.” Section 2.1. 3.4.

Where is the eave on a roof?

An eave is the edge of the roof that overhangs the exterior siding. Parts of an eave include the soffit, which is the underside of your roof’s eaves, and the fascia, the vertical facing board.

What is the overhang of a roof called?

What Is a Soffit? Your roof by necessity, will often times extend over the walls of your home. This overhang can go by a few names, such as the house eaves or the rafters of your roof. The underside of this overhang, when given a finished appearance, is known as the soffit, which means “something fixed underneath”.

Where does rake trim go?

Rake trim (also known as gable trim) is a metal flashing finishing piece placed along the roofline at the sloped sides at the end of a residence’s dormer or gable.

What is residential rake trim?

Residential rake trim is one of the finishing touches to flash the endwall edge of your overhang. This trim gives your home or building a sleek, professional appearance.

What is gable trim used for?

Gable trim is used to finish off the edge of your roof. It’s installed on the two high sides of the roof, not the low side of the roof that follows the pitch.

Why don t Texas homes have gutters?

That’s because water from rain or snow that is allowed to flow over your roof onto the ground surrounding your home can damage your foundation, which can be a costly repair.

How much should a gutter overhang?

A safe distance between the gutter and the roof edge should be between 2 to 3 inches. If the gutter distance is more than 3 inches, the rain will run off the roof and won’t drain properly.

Should gutters go past the roof?

Proper Placement for Your Gutter Installation Your gutters should extend beyond your roof shingles, not align with them. … When gutters are installed directly in line with your roof shingles, the shingles impair the natural flow of water. Rainwater can flow onto the end cap and will likely cause a drip.

Is gutter apron the same as drip edge?

A gutter apron serves the same purpose as a drip edge. … The most obvious attribute that distinguishes a gutter apron from a drip edge is the fact that a gutter apron is more of an L-shaped metal rather than a T. A gutter apron also comes in metal strips with aluminum and steel sheets.

What is the proper drop for gutters?

A good rule of thumb for a gutter slope is that you want at least a quarter inch of slope for every 10 feet of gutters.

Does drip edge go on first?

Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

How far under roof should gutters be?

3 Answers. 3-5 centimeters is in the 2-3 inch range. Any more and you run the risk of water running off the tile and overshooting the gutter. The gap can vary some because the gutters must slope towards the downspout.

How far should shingles overhang the rake?

The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.

Why does water leak from soffits behind gutters?

If the gutters are clogged, it’s possible that the water is overflowing the gutters and this is contributing to the leak. If the gutters look clear, run a hose and fill the gutters with water. Water should run out the downspout and away from the house without filling the gutter.

Should fascia be screwed or nailed?

Replacement fascia requires 4d galvanized casing nails. … Hometime.com recommends using screws instead of nails when replacing fascia to avoid jarring the existing framing with hammering.

Can you install drip edge after shingles?

Can Drip Edge Be Installed After Shingles? The most popular time to install a drip edge is when new shingles are installed. However, the drip edge can be installed at any time. The materials involved include: a ladder, a flat pry bar, a hammer, tin snips, eave stripping, and galvanized roofing nails.

How far should metal roof overhang?

A typical metal roof overhang may be 2 to 4 inches, or even less. Some slight overhang is recommended, in conjunction with a drip edge flashing, to prevent water from getting under the roofing and onto underlying wood.