What kind of screws do you use for Trex decking

DO NOT countersink screws. Use recommended stainless steel screws in any areas near bodies of saltwater. 2-3/4″ or 3″ screws can be used with Trex 2×6 product.

Can I use regular screws with Trex?

Composite decking can be fastened to treated wood joists with screws or with hidden fasteners. Using composite deck screws is critical because they are specially designed to help hold the material in place. … It is also important that all screws be secured at a 90-degree angle to the boards.

Can you use screws in Trex decking?

The answer is yes for a solid composite decking (must be pre-drill and must check with manufacture). You can not drill or screw through a hollow composite deck as the screw will become loose and rise in time . Like the usual wooden decking boards, you can also screw down a solid composite decking.

Do I need special screws for composite decking?

You can screw or nail composite decking boards just like wood ones. Three-inch decking screws are the best fastener choice; they sink a secure distance into the joists and won’t back out like nails. There’s little danger of splitting the boards when driving them, so you don’t need to pre-drill.

Should you pre drill Trex?

You do not have to pre- drill with Trex Escapes. Composite decking is a great alternative to traditional wood decking. When building your deck and railing, it is recommended that code-approved structural material be used as the framing and joists.

Can you face screw TimberTech?

TimberTech recommends the use of TimberTech TopLoc Face Fasteners for square shouldered plank installations. Cortex Hidden Fastening System may also be used for the installation of square shouldered planks.

What is the joist spacing for Trex decking?

The majority of composite deck board brands including Trex, TimberTech, and more require deck joists spacing to be at 16 inches O.C. (on center) for standard straight composite decking installation.

Do Trex hidden fasteners come with screws?

A: Every container of Trex Hideaway hidden fasteners includes the stainless steel screws needed for installation.

Can Trex be ripped?

Can you rip a Trex board? Trex products should not be ripped to reduce thickness, but can be ripped to reduce width. As long as the board can still be installed per the installation instructions, the warranty will be valid. Please use care when fastening ripped boards, as pre-drilling may be necessary.

Are Trex hidden fasteners worth it?

Hidden deck fasteners are a nice way to keep the surface of your deck looking clear and unencumbered. But they are not the right fastener for all decks. In fact, using hidden deck fasteners inappropriately is a formula for failure. Some deck projects require the stronger fastening power of face screws.

Article first time published on

What screws to use for fascia?

Replacement fascia requires 4d galvanized casing nails. After taking off a whole damaged fascia board, cut away all damaged wood and prepare to reinstall what good part remains; miter-saw the good part of the old board at a rafter connection. Use 2-inch galvanized deck screws to reattach the remains of the old board.

How many screws do I need for composite decking?

For standard composite decks with 6-inch wide boards and 16″ OC joists, you will need at least 350 screws for every 100 square feet. Since most hidden clip fastener systems require fewer screws, you will need at least 175 screws for the same square footage.

Is it hard to install Trex decking?

It’s Hard to Install It’s not hard to install. … With Trex Decking’s simple to install clip system, even amateurs can effectively install a new deck. Trex even provides simple how-to guides for those who want to make their deck a DIY project.

How do you secure the last piece of composite decking?

Position the clip on the outside of the rim joist securing it with a single screw inserted perpendicular to the joist. After positioning the last deck board in place, secure it by angling a screw through the clip and into the board at a 30˚- 45˚ angle.

How many Trex boards do I need for a 12x12 deck?

Board lengthBoards required8 FT20612 FT13716 FT10320 FT83

How do you hide the ends of Trex decking?

Composite decking ends can be finished by picture framing, raised fascia board, painting the ends, attaching decking veneer, composite nosing strips, vinyl stair nosing cove, composite corner trim or plastic end caps.

Do you gap Trex decking?

All deck boards must always be installed with a 6mm side-to-side gap. The Trex Hideaway Hidden Fasteners automatically measure the 6mm gap between grooved edge boards but you must still ensure the 6mm gap with the square edge boards.

Can you use Trex hidden fasteners on TimberTech?

Most hidden deck fasteners are compatible with the major decking brands like Trex, Timbertech or Azek. The benefit of grooving your own boards is that you can make the groove however you like.

Should you seal the ends of composite decking?

Kim Katwijk The cut ends of composite decking will absorb moisture and can swell, as shown here. Sealing the end cuts with lumber wax will help prevent swelling. … Because the uncapped ends of the boards are free to pick up water, the core can absorb moisture, which can lead to all sorts of problems.

Is Trex decking slippery when wet?

Trex decking is a low-maintenance decking solution that requires a fraction of the work of wood decks and is less likely to get slippery when wet. It still requires occasional attention to keep it looking its best, but you’ll be delighted with the finished results.

Can you pressure wash Trex?

Trex does not recommend the use of a pressure washer. The use of a pressure washer on deck surface could damage the decking surface and will void the warranty with respect to any condition caused by the pressure washing.

Can I use vinegar on Trex decking?

For mold removal, try cleaning composite decking with vinegar. Use your hose to remove as much of the surface grime and mold as possible. Mix two parts vinegar and one part water into a bucket and pour the solution directly on the mold. After the solution is poured, sprinkle some baking soda on the area.

How many hidden fasteners do I need for Trex?

You will need 0.75 clips for every lineal foot of decking. For example, 40 feet of decking would require 30 start clips. NOTE: When using hidden fasteners (both start and connector clips), one must be used on every joist.

What are hidden deck fasteners?

What Are Hidden Deck Fasteners? Hidden Deck Fasteners give your deck a smooth, unmarred surface. They can be used for composite decking, grooved boards, softwoods, hardwoods, and more! Check out all the different hidden fasteners available from trusted brands like CAMO, AZEK, and Trex at DecksDirect.